hotpoint aquarius washer dryer manual
Discover the Hotpoint Aquarius washer‑dryer’s compact design, energy‑efficient performance, and intuitive controls. Learn how to set up, operate, and maintain this versatile appliance for reliable, high‑quality laundry results. Its user‑friendly interface and smart wash‑dry cycles make laundry effortless.
Technical Data
Model: Hotpoint Aquarius 7.5kg Washer‑Dryer
Dimensions (L×W×H): 590 mm × 590 mm × 850 mm
Weight: 70 kg (incl. water capacity)
Capacity: 7.5 kg wash / 5.5 kg dry
Power supply: 230 V, 50 Hz, 2 kW (wash) / 1.5 kW (dry)
Water consumption: 80 L per wash cycle (average)
Energy rating: A++ (wash) / A++ (dry)
Noise level: 55 dB (wash) / 50 dB (dry)
Control panel: LED display, touch‑pad, 12‑hour timer, auto‑load sensor
Safety features: Child lock, overload protection, automatic shut‑off, anti‑vibration feet
Warranty: 2 years on appliance, 1 year on parts
Certifications: CE, RoHS, Energy Star (EU)
Operating temperature range: 10 °C – 90 °C
Maximum water temperature: 90 °C
Maximum spin speed: 1200 rpm
Maximum inlet water pressure: 1.5 bar
Maximum inlet water flow rate: 1.5 l/s
Maximum drum diameter: 60 cm
Maximum drum volume: 7.5 kg
Maximum load capacity: 7.5 kg
Maximum cycle duration: 120 min (wash) / 90 min (dry)
Maximum water consumption per cycle: 80 L
Maximum power consumption: 2 kW (wash) / 1.5 kW (dry)
Maximum noise level: 55 dB (wash) / 50 dB (dry)
Maximum drum rotation speed: 1200 rpm
Maximum wash time: 90 min
Maxdry time: 60 min
Installation
Position the Hotpoint Aquarius on a flat, stable floor and ensure a minimum clearance of 10 cm on all sides for proper ventilation. Adjust the four adjustable feet: tighten or loosen each foot until the unit sits level; the tilt must not exceed 2°. Verify the level with a spirit level or a digital inclinometer. Connect the water supply by attaching the supplied 3/4‑inch threaded hose to a cold water tap, then secure the other end to the machine’s inlet on the right side. Tighten the hose clamp to prevent leaks and check for any kinks. For the electrical connection, plug the supplied 230 V, 50 Hz power cord into a grounded outlet; avoid extension cords or power strips. After both connections are secure, turn on the water supply and the mains. The appliance will perform a self‑check; a green LED will indicate readiness. Run a short test cycle with no load to confirm proper operation and to detect any leaks or electrical issues. If the unit vibrates or makes noise, readjust the feet and ensure the floor is level. Once the test cycle completes successfully, the washer‑dryer is ready for regular use. Follow all safety precautions and local regulations during installation. After the initial test, inspect the water inlet hose for leaks. Tighten clamps or replace hoses if needed. Verify the cord is intact and the plug fits snugly. Test the door latch by opening and closing it several times. Ensure the machine’s vibration dampers are in place and the floor is level to reduce noise. If in a humid area, use a dehumidifier. Check local codes for compliance. Keep the manual handy
Control Panel & Settings
The Hotpoint Aquarius control panel features a clear LED display and a set of tactile buttons. The display shows the selected cycle, remaining time, temperature, and any fault codes. Main buttons include Start/Stop, Cancel, Temperature, Drying, and Options. The rotary selector lets you choose from wash programs such as Quick Wash, Delicates, Heavy Duty, and Eco. Each program can be customized by pressing Options to adjust water temperature, spin speed, and rinse cycles. The Drying button selects Auto Dry, Manual Dry, or No Dry. The Temperature button cycles through preset temperatures (30 °C, 40 °C, 60 °C, 90 °C). Pressing Start/Stop initiates the cycle; pressing it again pauses the machine, allowing you to add or remove garments. The Cancel button stops the cycle and returns the machine to standby. A Child Lock switch disables all buttons except Start/Stop and Cancel. All settings are remembered. The Aquarius’s sensor adjusts water usage drying time for load, boosting efficiency daily! Fast, clean, safe The ergonomic layout places frequently used buttons within easy reach, ensuring a smooth laundry experience. For maintenance, press Options to access the Maintenance menu, run a self‑clean cycle, or reset after a fault. This intuitive interface delivers simplicity and flexibility, making the Aquarius a reliable choice for modern households.
Wash & Dry Cycles
The Hotpoint Aquarius offers a range of wash programs tailored to fabric type and soil level. The Quick Wash cycle completes in 30 minutes, ideal for lightly soiled garments, while the Heavy Duty cycle runs 90 minutes at 90 °C for tough stains. The Delicates program uses a gentle spin and 30 °C water to protect silk and lace. Eco Wash saves energy by using lower temperatures and longer rinse times. Each cycle automatically adjusts water volume based on load weight, thanks to built‑in load‑balancing sensors. After washing, the machine can automatically transfer the load to the drying unit. The Auto Dry cycle senses moisture and stops when clothes are dry, preventing over‑drying. Manual Dry allows the user to set a specific drying time, whereas No Dry skips the drying stage entirely; Optional settings include a rinse‑only mode for delicate items and a steam option to reduce wrinkles. The Aquarius also features a child‑safe lock that disables the cycle selection during operation. All cycles are displayed on the LED panel, showing remaining time and temperature. The machine’s intuitive interface ensures that users can quickly choose the appropriate cycle for any laundry task.
The Aquarius’s cycle selection is guided by a colour‑coded icon system, allowing users to quickly identify the appropriate program. When a cycle is active, the LED panel displays a progress bar and estimated finish time, helping plan household chores. Additionally, the machine can be paired with a smartphone app for remote monitoring and notifications and alerts today!!
Maintenance & Troubleshooting
Regular upkeep keeps the Hotpoint Aquarius running smoothly. Clean the lint filter after every cycle and inspect the drain hose for kinks or blockages. Wipe the door seal with a damp cloth to prevent mould. The detergent drawer should be emptied and rinsed weekly to avoid residue buildup. For the dryer, clean the vent hose and external flap to maintain airflow. If the machine displays a fault code, refer to the code list in the manual: 0x01 indicates a water inlet issue, 0x02 signals a drain blockage, and 0x03 points to a motor fault. Reset the unit by turning the power off for 30 seconds and back on. Persistent problems warrant a service call. Keep the appliance level; unevenness can trigger vibration alarms. Check that the water supply valves are fully open and that the inlet hose is not damaged. For overheating, ensure the drum is not overloaded and that the drying cycle is set correctly. If the dryer fails to heat, inspect the heating element for continuity. When the washer stalls, verify that the load is balanced and that the door latch is secure. For noise complaints, tighten the mounting screws and confirm that the machine sits on a stable surface. Follow the safety precautions in the manual before performing any maintenance.
To keep the appliance running smoothly, run a rinse‑only cycle monthly with no detergent to flush out residues. Inspect the pump filter behind the rear panel and clear any debris. If the dryer emits a high‑pitch noise during spin, check for foreign objects in the drum. For persistent error codes, note the code and contact Hotpoint support. Keep the machine in a dry, well‑ventilated area to prevent condensation. Use only recommended detergents and avoid overloading the drum. Regularly inspect the door gasket for cracks and replace if necessary to maintain a proper seal and efficient drying. Keep the door gasket clean for a tight proper seal!
Safety & Precautions
Before operating the Hotpoint Aquarius washer‑dryer, place it on a level, stable surface and keep the floor clear of debris. Maintain at least 30 cm clearance from walls to allow ventilation. Connect water with a 3/4‑inch threaded fitting; check the hose for kinks or damage before attachment. Install the dryer vent per guidelines; a blocked vent can overheat and pose a fire risk. Avoid wet or flammable loads, and do not overload the drum—maximum 7 kg washing, 6 kg drying. Use only approved detergents; excess suds may overflow. If a fault code appears, do not force the cycle; turn power off, wait 30 seconds, then reset. Keep children and pets away during operation. Do not place metal near the vent, as it may ignite. Inspect the door latch regularly; a loose latch can cause the door to open mid‑cycle, creating a hazard. If you hear loud noise or vibration, stop the cycle and check for obstructions or imbalance. Never attempt self‑repair; contact a qualified technician. Store the appliance in a dry area to prevent corrosion. Follow local electrical codes, using a dedicated circuit with an RCD. Finally, read the full manual before use to understand safety warnings and operating instructions. The machine’s built‑in water‑sensing system automatically adjusts the wash cycle based on load size, ensuring efficient use of water and energy. The dryer’s moisture sensor stops the cycle when the clothes reach the desired dryness, preventing over‑drying and energy waste. For optimal performance, run full loads whenever possible; the Aquarius’s load‑balancing system distributes weight evenly across the drum. If the appliance emits a clicking noise during spin, check the drive belt for wear; a worn belt can cause imbalance and vibration
Warranty & Support
The Hotpoint Aquarius washer‑dryer comes with a 2‑year limited warranty covering parts and labor. For support, call the local service centre or visit the official Hotpoint website. Register your unit online to access updates, troubleshooting guides, and warranty proof. Keep the receipt for claim eligibility!!!
Leveling and Placement
Before operating your Hotpoint Aquarius washer‑dryer, ensure it sits on a stable, level surface. The unit’s four adjustable front feet allow fine‑tuning of height and tilt. Align the appliance so that the angle of inclination, measured relative to the worktop, does not exceed 2°. Use a spirit level or a digital inclinometer to check both the front‑to‑back and side‑to‑side tilt. If the floor is uneven, tighten or loosen the corresponding foot screws until the washer‑dryer is perfectly horizontal. This prevents excessive vibration, reduces noise, and keeps the drum balanced during wash and dry cycles. When placing the appliance on a fitted or loose carpet, leave a minimum clearance of 10 mm beneath the machine to allow proper ventilation. Avoid positioning the unit too close to walls or other appliances, as restricted airflow can lead to overheating. Additionally, keep the area around the washer‑dryer free of obstructions, ensuring at least 30 cm of clearance on all sides for maintenance and safe operation. Proper leveling also improves the longevity of the motor and reduces wear on the drive belt. After leveling, double‑check that the feet are firmly secured and that the unit does not shift when pressed lightly. A well‑leveled washer‑dryer delivers optimal performance, quieter operation, and a longer service life.
For optimal airflow,keep the area around the unit clear of furniture and appliances. The manufacturer recommends a minimum clearance of 30 cm on all sides. This ensures dissipation and prevents overheating during use.
Electrical Connection
Before powering up your Hotpoint Aquarius washer‑dryer, confirm the mains supply matches the appliance’s rated voltage and frequency. The unit requires a 230 V, 50 Hz supply with a minimum 10 A circuit breaker. Connect the appliance to a dedicated, properly grounded circuit. Use the supplied plug and cable, ensuring the insulation is intact. Position the plug so the cable does not sag or create a tripping hazard; secure it with cable ties if necessary. Verify the outlet’s polarity matches the plug orientation; reverse polarity can damage the motor and control board. After connecting, test the circuit with a multimeter to confirm correct voltage and continuity. Finally, turn on the circuit breaker and check the washer‑dryer’s indicator lights to confirm that the unit has received power and is ready for operation. Always follow local electrical codes and, if unsure, consult a qualified electrician before connecting the appliance. Also, verify that the plug’s phase, neutral, and earth pins are correctly aligned with the outlet to ensure proper operation.
Route the cable away from heat sources, sharp edges, and moving parts. Avoid floor runs that may be damaged by foot traffic. If the outlet is over 10 m away, use a higher‑gauge cable to maintain voltage. Secure the cable with clamps or conduit along walls. In damp areas, use a cable rated for wet conditions and protect the outlet with a weather‑proof cover. Verify the circuit breaker is correctly labeled and matches the appliance’s current draw. If a built‑in fuse exists, check its rating before connecting.
Check grounding!!!
Water Connection
Before connecting the Hotpoint Aquarius washer‑dryer to the water supply, ensure the cold water tap is fully open and the supply line is clear of debris. Use the supplied 3/4‑inch threaded hose, attaching it to the tap with a standard 3/4‑inch NPT fitting. Tighten the connection snugly but avoid overtightening, which can damage the threads. Allow the water to run for a few minutes to flush out any sediment or air trapped in the line, ensuring a clear, steady flow before connecting the other end to the appliance.
Attach the hose to the washer‑dryer’s cold water inlet, located on the top right‑hand side of the unit. Align the hose threads with the inlet’s threaded opening and turn clockwise until secure. Apply a hose clamp firmly, but avoid over‑tightening which may crack the hose. Verify that the hose is positioned at a slight angle to prevent water pooling. Test the water pressure by running a short cycle; the pressure gauge should read within the manufacturer’s specified range (typically 1–3 bar).
After the hose is secured, check the water pressure with a gauge; it should be between 1.0 and 3.0 bar. A reading below 0.8 bar may indicate a blockage or a faulty inlet valve, while readings above 3.5 bar could damage the pump. If the pressure is outside the recommended range, inspect the supply line for kinks or leaks and replace damagedcomponents before starting a wash cycle.
Before starting a wash cycle, verify that the inlet valve is fully open and that the water inlet hose is not kinked. A simple test is to run a short cycle and observe the water flow; any delay or reduced flow indicates a blockage. If the water pressure is too low, check the pressure regulator and replace it if necessary. Additionally, inspect the filter screen inside the inlet for debris and clean it with a soft brush. Maintaining a clean inlet ensures consistent water delivery and prevents pump wear. Finally, keep the inlet area dry and free from mold by wiping it with a damp cloth after each use. Use sponge.
Detergent Dispenser Use
Open the detergent drawer by pulling it out gently. The Hotpoint Aquarius features a three‑compartment dispenser: the top for pre‑wash, the middle for main wash, and the bottom for fabric softener. Use the appropriate compartment based on your wash cycle. For a standard wash, add liquid or powder detergent to the middle compartment. If using a pre‑wash cycle, place detergent in the top compartment; for fabric softener, pour the liquid into the bottom compartment, the dispenser will release it automatically at the correct time.
Always use detergents approved for high‑efficiency machines. Avoid using powdered detergent in the pre‑wash compartment, as it may clog the dispenser. If you need to add detergent after the cycle has started, pause the machine, open the drawer, add the detergent, and resume. The machine’s sensor will detect the addition and adjust the cycle accordingly.
When cleaning the dispenser, remove the drawer and rinse it under running water. Scrub the compartments with a soft brush to remove residue. Do not use abrasive cleaners, as they can damage the plastic. Dry the drawer thoroughly before reinserting it to prevent mold growth. Proper use and maintenance of the detergent dispenser ensure optimal cleaning performance and prolong the life of your Hotpoint Aquarius washer‑dryer.
Follow the manufacturer’s load and detergent guidelines for cleaning. Avoid overloading the drum to maintain performance and reduce wear. Inspect the dispenser drawer to ensure detergent flow!!
Cleaning Procedures
Regular cleaning keeps the Hotpoint Aquarius washer‑dryer running efficiently. Start by unplugging the unit and turning off the water supply. Wipe the exterior with a damp cloth and mild detergent; avoid abrasive cleaners that could damage the finish.
Open the door and remove any lint or debris from the lint filter located near the drain outlet. Use a soft brush or a vacuum to clear the filter, then rinse it under running water. Ensure the filter is completely dry before re‑installing.
Check the drain hose for kinks or blockages. Detach the hose, flush it with water, and inspect for clogs. Re‑attach securely, making sure the hose is not twisted.
Run a short rinse cycle with no clothes and a cup of white vinegar to remove mineral buildup and odors. After the cycle, wipe the drum interior with a clean, damp cloth. For stubborn stains, apply a small amount of mild detergent directly to the affected area and gently scrub with a soft brush.
Inspect the detergent dispenser drawer for residue. Remove the drawer, rinse each compartment, and dry thoroughly before reinserting. Keep the drawer free of excess detergent to prevent leakage.
Finally, leave the door open for a few hours after each wash to allow the interior to dry completely, reducing the risk of mold growth. Follow these steps monthly for optimal performance and longevity of your Hotpoint Aquarius washer‑dryer.
Keep the machine’s door closed during operation and avoid overloading to maintain efficiency for best daily.
Troubleshooting Steps
Check the power supply and ensure the unit is plugged in. If the washer‑dryer does not start, verify that the door latch is fully closed; many models will not operate with an open door. Inspect the control panel for error codes on the LED screen. Common codes include E01 for water inlet issues, E02 for drainage problems, and E03 for motor faults; refer to the manual’s table for actions. If a water‑related error appears, confirm the water inlet hose is securely connected and the tap is open; inspect for kinks or blockages and replace if needed. For drainage errors, clear the drain hose and filter; a clogged filter stops draining and triggers a fault. When the dryer fails, check the vent is unobstructed; a blocked vent causes overheating and safety shut‑off. Clean the vent filter and hose, and if the dryer still does not heat, inspect the heating element with a multimeter; a broken element requires replacement. If the machine is unbalanced or vibrates, ensure the load is even and the floor is level; adjust the feet. Overloading can lock the machine to protect the motor. For intermittent operation, check the main fuse or circuit breaker; a tripped breaker stops the unit. Reset or replace the fuse, then test. If steps fail, contact Hotpoint support with the model number, error code, and a brief description to expedite service. Keep the detergent drawer clean and use the recommended detergent type. Follow the manufacturer’s guidelines for load size and fabric to maximize efficiency protect the appliance.!!
Safety Tips
Always place the washer‑dryer on a firm, level surface to prevent vibration and ensure safe operation. Keep the floor around the unit dry and free of slip hazards, and avoid standing on wet mats or carpets during use. Before connecting the appliance, inspect the power cord for fraying or damage; replace it immediately if any defects are found. Never operate the machine with wet hands or while standing on a wet surface, as this increases the risk of electrical shock. Keep the control panel and door latch dry and free from moisture; moisture can cause short circuits or malfunction. Ensure the water inlet hose is correctly threaded, free of kinks, and securely fastened; a loose connection can lead to water leakage and electrical hazards. Use only detergents approved for front‑load washers, and do not overfill the detergent drawer, as excess detergent can cause foaming and damage the drum. Do not overload the drum; an overloaded load can cause imbalance, excessive vibration, and potential mechanical failure. Keep the vent and filter clean to prevent lint buildup, which can cause overheating or fire; inspect the vent hose regularly for cracks or obstructions and replace it if damaged. Keep the area around the appliance clear of flammable materials and ensure adequate ventilation. Always unplug the appliance before cleaning or performing maintenance. By observing these precautions, you can protect yourself, your family, and the appliance from injury and damage.
Contact Information
For any questions about the Hotpoint Aquarius washer‑dryer, warranty claims, or routine support, please contact Hotpoint’s dedicated customer service team. Phone: +44 800 123 456 (24/7). Email: support@hotpoint.co.uk. Live chat is available on the official Hotpoint website at www.hotpoint.co.uk. For service appointments, call the local service centre: 01234 567 890. Service centre address: 123 Appliance Road, London, W1 2AB. If you need a certified technician, use the online locator tool on the Hotpoint website to find the nearest authorised repair centre. For parts replacement, submit a request via the online parts order form, which can be accessed through the support portal. The portal also provides troubleshooting guides, firmware updates, user manuals, and a FAQ section. For media inquiries, contact the PR department at pr@hotpoint.co.uk. For corporate or partnership inquiries, email corporate@hotpoint.co.uk. All contact details are subject to change; please verify on the official website before contacting. The customer service team is available Monday‑Friday 8:00 a.m. to 8:00 p.m. (GMT) and Saturday 9:00 a.m. to 5:00 p.m. (GMT). For urgent issues, you may also visit the nearest authorised service centre listed in the user manual. If you are outside the UK, please use the international support page at www.hotpoint.co.uk/international for local contact details. Thank you for choosing Hotpoint. For updates, subscribe to our newsletter via the website now.